Sunday, April 28, 2024

TI 30Xa Algorithms: Fundamental Horizontal Circle Calculations

 TI 30Xa Algorithms: Fundamental Horizontal Circle Calculations



Introduction and Formulas





Given the following:


r = radius of the curve

Δ = central angle, or the angular sweep of the curve. The angle is usually given in whole degrees or in surveying, degrees-minutes-seconds.


We can calculate the following:


The length of the tangent line to the central meeting point:

t = r × tan( Δ / 2 )


The linear distance from where the curve begins to the point the curve ends, known as the chord distance:

c = 2 × r × sin( Δ / 2 )


The distance of the curve from the end points, known as the arc length:

s = (Δ° / 180°) × π × r


Note the formula for arc length assumes that the angle is in degrees. If the angle is in radians, the formula for arc length reduces to s = Δ rad × r.



Procedure


The procedure is made for the TI-30Xa, where we can take advantage of the three memory registers it has. You can use another calculator, except most basic scientific calculators only have one memory register; you will just have type in one of the extra variables.


1. Check the angle mode. We should be in degrees mode, which is indicated by the DEG indicator. If not, press the [ DRG ] key until degrees mode is selected.


2. Enter the central degree (Δ).


If the degree is in whole degrees, just enter the angle and store into memory register 1. ( [ STO ] [ 1 ] ).


If the degree is in degrees-minutes-seconds format (known as DMS or sometimes as HMS), enter the angle in DD.MMSSS format. Then press [ 2nd ] [ + ] {DMS>DD} to convert the angle into whole degrees. Then store the result into memory register 1.


3. Enter the radius length and store in memory register 2. ( [ STO ] [ 2 ] ).


Memory registers:

M1 = Δ; M2 = r


4. Calculate the tangent length, t:


[ ( ] [ RCL ] 1 [ ÷ ] 2 [ ) ] [ TAN ] [ × ] [ RCL ] 2 [ = ]


5. Calculate the chord distance, c:


2 [ × ] [ RCL ] 2 [ × ] [ ( ] [ RCL ] 1 [ ÷ ] 2 [ ) ] [ SIN ] [ = ]


6. Calculate the arc length, s:


[ RCL ] 1 [ × ] [ π ] [ × ] [ RCL ] 2 [ ÷ ] 180 [ = ]


Examples


Let’s assume for the following examples Degrees mode is set (DEG).


Example 1:

r = 150 ft (it can be any length unit as long as you keep it consistent)

Δ = 60° (whole degrees)


60 [ STO ] 1

150 [ STO ] 2


t: [ ( ] [ RCL ] 1 [ ÷ ] 2 [ ) ] [ TAN ] [ × ] [ RCL ] 2 [ = ]

t = 86.60254038 ft


c: 2 [ × ] [ RCL ] 2 [ × ] [ ( ] [ RCL ] 1 [ ÷ ] 2 [ ) ] [ SIN ] [ = ]

c = 150 ft

(In this case, the chord length is the same as the radius. Why? There is a geometric reason.)


s: [ RCL ] 1 [ × ] [ π ] [ × ] [ RCL ] 2 [ ÷ ] 180 [ = ]

s = 157.0796327 ft



Example 2:

r = 324 ft

Δ = 92°22’18” (92 degrees, 22 minutes, 18 seconds)


92.2218 [ 2nd ] [ + ] {DMS>DD} [ STO ] 1

324 [ STO ] 2


t: [ ( ] [ RCL ] 1 [ ÷ ] 2 [ ) ] [ TAN ] [ × ] [ RCL ] 2 [ = ]

t = 337.6968953 ft


c: 2 [ × ] [ RCL ] 2 [ × ] [ ( ] [ RCL ] 1 [ ÷ ] 2 [ ) ] [ SIN ] [ = ]

c = 467.5897175 ft


s: [ RCL ] 1 [ × ] [ π ] [ × ] [ RCL ] 2 [ ÷ ] 180 [ = ]

s = 522.3494689 ft



Source

Hewlett-Packard Company. HP-46 sample applications. Loveland, CO. February 1,1975. Part No. 00046-90018. pg. 104-105



Happy Birthday, Smokey!


Eddie


All original content copyright, © 2011-2024. Edward Shore. Unauthorized use and/or unauthorized distribution for commercial purposes without express and written permission from the author is strictly prohibited. This blog entry may be distributed for noncommercial purposes, provided that full credit is given to the author.